Having made a few long bows before, I wanted to try something a bit different. All of them could shoot an arrow, but they would kick quite badly or broke after a couple of hundred shots. So I decided, after reading the bowyers bible, that I wanted to make a flat bow (Confusingly Americans call it a long bow).
The difference in design it that the limbs (the bendy bits of wood that give the bow its power), are much wider and shallower than the English style Longbow (which I had based my earlier bows on). This means the extremes in compression and tension within the wood are reduced but the extra width in the limb maintains the the bows power. Also the handle section on a flatbow is stiff, this reduces the shock that can be felt when the arrow is shot.
So I started by removing the bark, checking the wood underneath, as there seemed little to worry about, I marked the bow up ready for cutting. Below you can see the basic design I followed
I then took the bow to a friend of mine who cut out the marked up shape with a band-saw. I was a little apprehensive about using a band-saw on the bow stave because; a - it can ruin it very quickly and b - I have only used hand tools on bows previously.
Yew has a unique property that makes it an ideal wood for making bows with. The heartwood (the wood that grows in the center of the trunk) resists compression very well. And the sapwood (the bit that grows on the outside of the trunk) resists tension. So when making a bow you need to put the sapwood on the "Back" of the bow, this is the bit that is facing away from you when you point it at a target (The part facing toward you is called the Belly).
So to get the bow working as efficiently as possible I needed to reduce the amount of sapwood on the stave so the finished bow will contain both heart and sapwood (the sapwood is too thick otherwise).
To take full advantage of the wood's natural strength, I wanted the back of the bow to be one single intact growth-ring. This will reduce the risk of a ring lifting and causing a spilt and ultimately causing the bow to break. So I did this by selecting a ring that looks wide enough to work easily and is far enough into the sapwood to serve as the back of the bow. I then used a draw knife to peel and prize away the wood down to about 1 ring above the one I selected. When I get to knots, I leave them at this stage. Maybe take of a few rings around them but it's very easy to chop straight through the selected ring.
 |
| Growth rings |
 | |
| working around a knot |
 |
| finished the back of the bow |
The next stage was to remove the wood from the belly of the bow, this is a very time consuming process. I use a draw knife to reduce the the limbs to about 1" deep, I don't want to go much further with the draw knife as it doesn't deal very well with knots etc. You can end up ripping large swathes of material from the bow and before you know it - you have gone too far.
 |
| This is the point I stop using the drawknife |
 |
| Growth rings on the belly of the bow all pointing roughly down the centre |
The next stage is a process is called "Tillering". The aim of tillering is to get the bow to a point where all of the wood is working evenly, ensuring that one part of the limb doesn't bend more than another (known as hinges), so creating an even curve when the bow is at full draw.
As soon as the bow can be bent, its worth checking the tiller very roughly to ensure you don't have any hinges that need to be delt with immediately. This can be done by putting the tip on the floor, holding the other end and the pushing on the handle, don't push too hard, just so you can see the curve of the limb. If this looks OK carry on evenly reducing the belly. This isn't a very accurate indication of tiller but it does help in the early stages. If you can see any hinges, mark the area that is bending more than the rest of the limb. Then when you are reducing on the limb, just don't take anything off that area until the limb stops hinging.
Once the bow can be bent a bit more, I then use a tillering stick, a piece of wood about 40" long, with a cradle at one end to hold the bow and a load of notches down one edge to hook the string on to.
I then cut some nocks in to the end of the limbs, I use a rat tail file for this. They want to be about 1/2" - 3/4" from the tips of the limbs. I use a long string (a bit longer than the bow) with a timber hitch at one end and a loop at the other.
Put the string on the bow so its slack, put the bow on the tillering stick. Pull the string so it starts to bend and hook the string on to one of the notches. Stand back and inspect the bow checking for even bending and hinges. Use a pencil to mark areas that are bending too much a carry on reducing the limbs leaving the hinges.
Its worth noting that you should never draw a bow to more than its what you want its final weight to be. You can check this by putting the butt of the tillering stick on some bathroom scales when you are pulling the string back.
You also need to make sure the both limbs are bending evenly, if you have a large piece of card you can mark out a chart on to it indicating limb tip deflex, or you can use patio doors( if they are fairly symmetrical).
 |
| using the tillering stick and patio doors method |
So I just repeat this process, shortening the string, by adjusting the timber hitch, until I have got the bows brace height (the distance between the belly and the string when the bow is strung but not pulled) to where I want it (about 6 1/2 - 7"). Then until I can get the string back to my drawlength.
This will take ages to get right, don't rush it. As you get closer to your desired weight and draw length only use a cabinet scraper to reduce the the belly.
After tillering, I used a heat gun to heat the last 8-10 inches of the limb whilst its clamped in to a reflex shape. Not too much as it will add more strain in these bits of the limb. Leave it to cool whilst clamped. This just adds a bit more poke and makes it a bit smoother to draw.
 |
| adding reflex to the tips |
Then I used superglue to glue layers buffalo horn with other pretty bits of wood (in this case bamboo) to make the knocks. I then shaped them with some files and sandpaper
 |
| gluing up tips |
 |
| Nice tips |
Sand it back going from p 100 to p 320 then some fine wire wool, I finish it with 3 layers of danish oil, then some pre-cat lacquer, and then some beeswax furnature polish
Then add a leather handle
 |
| Slightly dodgy looking handle |
Take a picture of it in the snow
 |
| bow in snow |
Then Shoot it
 |
| Me looking very serious |
The final bow is about 65 lbs @ 30" and 71" long but It will probably reduce in weight a little (I hope) as I shoot it.
P.S. This is how I make a bow and by no means definitive , I am not a trained bowyer, I have read bits and learned bits myself, then wrote it here so other people like me can read it and geek out a bit.
P.P.S.S. Be careful when you are making bows, a limb exploding has quite a lot of oomph and could hurt. Also yew is poisonous so use a mask when working with it, especially sanding.
